Lek og lær med teknologi · Dagens elever er morgendagens innovatører
Lek og lær med teknologi · Dagens elever er morgendagens innovatører

Monk Makes CO2 Sensor for micro:bit

Før pris 1.749 kr - Før pris 1.749 kr
Før pris
Eks. mva: 1.399 kr
Ink. mva: 1.749 kr
1.749 kr - 1.749 kr
Nå pris
Fjernlager
  • Bestill på nett: Betal med Vipps, kortbetaling eller faktura (EHF-faktura for skoler og bedrifter)
  • Bestill via telefon: Ring 35 60 02 01 (man-fre 9-15)
  • Bestill via e-post: salg@n00b.no

Dette brettet, designet for bruk med Lets Talk Science Living Space Project, gir en CO2-, temperatur- og relativ fuktighetsmåling til en BBC-microbit.

Krokodilleklemmer medfølger ikke.

Kom i gang

Wire-up the board to your micro:bit as shown above. Then flash the following program onto your micro:bit by clicking the image to open the blocks editor and then click on Download (bottom of the web page) and copy the hex file onto your micro:bit.

Klikk på bildet for å komme til koden, eller følg linken:
https://makecode.microbit.org/90724-39395-51429-15821

Once the program is uploaded, pressing Button A will display the CO2 level in parts per million of CO2. Pressing button B will display the temperature in degrees C and both buttons together will show the relative humidity.

If you are wondering about the big gray serial redirect block in the on start block, well this block starts serial transfer of data between the micro:bit and the CO2 sensor.

MicroPython

You can also use the board with MicroPython as the following code example shows.

Unless you are interested in the serial protocol used, you may want to copy the code below into your program and make use of the functions get_co2(), get_tempC() and get_rh().

from microbit import *

uart.init(tx=pin0, rx=pin1)

co2 = 0
tempC = 0
rh = 0

def check_incoming_messages():
    global co2, tempC, rh
    if uart.any():
        response = str(uart.read(), 'UTF-8')
        if len(response) < 8:
            return
        cmd_letter = response[1]
        cmd_value_str = response[2:8]
        value = int(cmd_value_str)
        if cmd_letter == 'Z':
            co2 = value
        elif cmd_letter == 'T':
            tempC = (value - 1000) / 10.0
        elif cmd_letter == 'H':
            rh = value / 10
            
def get_co2():
    uart.write('Z\r\n')
    sleep(100)
    check_incoming_messages()
    return co2
    
def get_tempC():
    uart.write('T\r\n')
    sleep(100)
    check_incoming_messages()
    return tempC

def get_rh():
    uart.write('H\r\n')
    sleep(100)
    check_incoming_messages()
    return rh
    
# Copy the code above into your program and then use the functions
# get_co2, get_tempC and get_rh in your own code

while True:
    display.scroll(get_co2())
    if button_a.was_pressed():
        display.scroll('T=' + str(get_tempC()))
    if button_b.was_pressed():
        display.scroll('RH=' + str(get_rh()))
    sleep(500)

CO2 Concentrations

So, what do these readings mean?

Fresh outdoor air should give a reading of around 400. In a smallish room with a few people in it, this will rapidly rise above 1000, as people breathe out CO2. If it gets above 2000 then your air is getting dangerously unhealthy.

Calibration

Your sensor is a sensitive scientific instrument and the readings it gives will gradually get less accurate. If you leave the sensor powered-up in a well ventilated room for 24 hours, then it will calibrate itself automatically.

You can also force calibration using the Calibrate CO2 block in the COZIR blocks category. This will set the sensor’s readings back to 400. So you should run this block only after the sensor has been in fresh air for 30 mins or so.

Altitude Compensation

If you live somewhere high up, then you need to tell the sensor about this by putting a Set Altitude block into your On Startup block and then changing its number to your altitude above sea-level in meters.

Battery Power

Once you have the code all working, you can disconnect the USB power and instead power the CO2 Sensor Board through the DC barrel jack using either a battery pack or a DC adapter. In both cases the power supply should be of between 5 and 9V.

Viktig: When powered by batteries in this way, the CO2 sensor will provide power back to the micro:bit. But make sure you have the power leads connected right between the CO2 sensor board and the micro:bit or your micro:bit could be damaged.